{"id":422,"date":"2015-11-30T16:19:17","date_gmt":"2015-11-30T16:19:17","guid":{"rendered":"http:\/\/sitepourvtc.com\/?p=422"},"modified":"2022-03-02T13:24:47","modified_gmt":"2022-03-02T13:24:47","slug":"pressurizer","status":"publish","type":"post","link":"https:\/\/sitepourvtc.com\/pressurizer\/","title":{"rendered":"Pressurizer"},"content":{"rendered":"
A pressurizer<\/strong> is a component of a pressurized water reactor<\/a>. Pressure in the primary circuit<\/strong> of PWRs is maintained by a pressurizer<\/strong>, a separate vessel that is connected to the primary circuit (hot leg) and partially filled with water which is heated to the saturation temperature<\/strong> (boiling point) for the desired pressure by submerged electrical heaters<\/strong>.<\/div><\/div>\n
\"pressurizer\"<\/a>
A pressurizer is a key component of PWRs.<\/figcaption><\/figure>\n

Temperature in the pressurizer can be maintained at 350 \u00b0C (662 \u00b0F), which gives a subcooling margin (the difference between the pressurizer temperature and the highest temperature in the reactor core) of 30 \u00b0C. Subcooling margin is very important safety parameter of PWRs, since the boiling in the reactor core must be excluded. The basic design of the pressurized water reactor<\/strong> includes such requirement that the coolant (water) in the reactor coolant system must not boil. To achieve this, the coolant in the reactor coolant system is maintained at a pressure sufficiently high that boiling does not occur at the coolant temperatures experienced while the plant is operating or in an analyzed transient.<\/p>\n

<\/span>Gas Compression in Pressurizer<\/div>
Pressure in the primary circuit<\/strong> of PWRs<\/a> is maintained by a pressurizer<\/strong><\/a>, a separate vessel that is connected to the primary circuit (hot leg) and partially filled with water which is heated to the saturation temperature<\/strong><\/a> (boiling point) for the desired pressure by submerged electrical heaters<\/strong>. During the plant heatup<\/strong> the pressurizer can be filled by nitrogen instead of saturated steam<\/a>.<\/p>\n

Assume that a pressurizer contains 12 m<\/strong>3<\/sup><\/strong> of nitrogen at 20\u00b0C<\/strong> and 15 bar<\/strong>. The temperature is raised to 35\u00b0C<\/strong>, and the volume is reduced to 8.5 m<\/strong>3<\/sup><\/strong>. What is the final pressure of the gas inside the pressurizer? Assume that the gas is ideal.<\/p>\n

Solution:<\/strong><\/p>\n

Since the gas is ideal,we can use the ideal gas law<\/strong><\/a> to relate its parameters, both in the initial state i <\/strong>and in the final state f<\/strong>. Therefore:<\/p>\n

pinit<\/sub>Vinit<\/sub> = nRTinit<\/sub><\/em><\/strong><\/p>\n

and<\/p>\n

pfinal<\/sub>Vfinal<\/sub> = nRTfinal<\/sub><\/em><\/strong><\/p>\n

Dividing the second equation by the first equation and solving for pf<\/sub><\/em><\/strong> we obtain:<\/p>\n

pfinal<\/sub> = pinit<\/sub>Tfinal<\/sub>Vinit<\/sub> \/ Tinit<\/sub>Vfinal<\/sub><\/em><\/strong><\/p>\n

Note that we cannot convert units of volume and pressure to basic SI units, because they cancel out each other. On the other hand we have to use Kelvins instead of degrees of Celsius. Therefore Tinit<\/sub> = 293 K and Tfinal<\/sub> = 308 K.<\/p>\n

It follows, the resulting pressure in the final state will be:<\/p>\n

pfinal<\/sub> <\/em><\/strong>= (15 bar) x (308 K) x (12 m<\/em>3<\/sup>) \/ (293 K) x (8.5 m3<\/sup><\/em>) =<\/em> 22 bar<\/em><\/strong><\/div><\/div>

<\/span>Enthalpy of Water - 0.1 MPa, 3 MPa, 16 MPa<\/div>
Latent heat of vaporization \u2013 water at 0.1 MPa (atmospheric pressure)<\/p>\n

hlg<\/sub> = 2257 kJ\/kg<\/strong><\/p>\n

Latent heat of vaporization \u2013 water at 3 MPa (pressure inside a steam generator)<\/p>\n

hlg<\/sub> = 1795 kJ\/kg<\/strong><\/p>\n

Latent heat of vaporization \u2013 water at 16 MPa (pressure inside a pressurizer<\/a>)<\/p>\n

hlg<\/sub> = 931 kJ\/kg<\/strong><\/p>\n

See also: Enthalpy of Vaporization<\/a><\/p>\n

\"Latent<\/a>
The heat of vaporization diminishes with increasing pressure, while the boiling point increases. It vanishes completely at a certain point called the critical point.<\/figcaption><\/figure>\n<\/div><\/div><\/div>\n
\n

Functions<\/h2>\n
\"Extensive<\/a>
Extensive and intensive properties of medium in the pressurizer.<\/figcaption><\/figure>\n

Pressure<\/strong><\/a> in the pressurizer is controlled by varying the temperature of the coolant in the pressurizer. For these purposes two systems are installed. Water spray system<\/strong> and electrical heaters system<\/strong>. Volume of the pressurizer (tens of cubic meters) is filled with water on saturation parameters and steam. The water spray system (relatively cool water – from cold leg) can decrease the pressure in the vessel by condensing the steam<\/strong> on water droplets sprayed in the vessel. On the other hand the submerged electrical heaters are designed to increase the pressure by evaporation the water<\/strong> in the vessel. Water pressure in a closed system tracks water temperature directly; as the temperature goes up, pressure goes up.<\/p>\n

Over-pressure relief system<\/h2>\n

Part of the pressurizer system is an over-pressure relief system<\/strong>. In the event that pressurizer pressure exceeds a certain maximum, there is a relief valve<\/strong> called the pilot-operated relief valve (PORV) on top of the pressurizer which opens to allow steam from the steam bubble to leave the pressurizer in order to reduce the pressure in the pressurizer, thus leads to reduction of pressure in the whole system. This steam is routed to a large relief tank \u00a0in the reactor containment building<\/a> where it is cooled and condensed back into liquid and stored for later disposition. There is a finite volume to these tanks and if events deteriorate to the point where the tanks fill up, a secondary pressure relief device on the tank(s), often a rupture disc, allows the condensed reactor coolant to spill out onto the floor of the reactor containment building<\/a> where it pools in sumps for later disposition.<\/p>\n

The pressurizer is equipped also with safety valves system<\/strong> (“safety system”), which are also\u00a0routed to the\u00a0relief tank.\u00a0The safety valves\u00a0system is used to emergency pressure reduction during emergency conditions.<\/p>\n

Water level monitoring<\/h2>\n

Since the reactor coolant system is completely flooded during normal operations, there is no point in monitoring coolant level in any of the other vessels. But early awareness of a reduction of coolant level<\/strong> (or a loss of coolant) is very important to the safety of the reactor core. The pressurizer is deliberately located high in the reactor containment building such that, if the pressurizer has sufficient coolant in it, one can be reasonably certain that all the other vessels of the reactor coolant system (which are below it) are fully flooded with coolant. There is therefore, a coolant level monitoring system<\/strong> on the pressurizer and it is the one reactor coolant system vessel that is normally not full of coolant.<\/p>\n

\u00a0<\/strong><\/strong>Main components of pressurizer<\/h2>\n